Tous les messages

Hobbyboy 18/03/2021
11
Recommandations
Commentaires (1)
Hobbyboy 30/08/2022
10
Recommandations
Commentaires (2)

Q: Is this model Expanded Poly Styrene, coffee cup foam?

demandé par Hobbyboy sur 2022-11-13 05:58:14

Zathrys No.This model is EPO.

2023-01-19 03:08:57 Utile (0)
Soumettre
réponses (1)

Q: why my high atitude show negatif value..gps problem or this fc problem

demandé par Songjihyo sur 2023-01-18 05:59:03

Hobbyboy once you have everything set up. you need to go inside the menu and do so calibration to the settings. All set up and trouble shooting is done inside the osd menu.

2023-01-18 01:07:08 Utile (0)
Soumettre
réponses (1)

Hobbyboy You will need to set up a 3pos on ch.5. This will give manual mode, fence, and rth. You will need to flip the switch into rth mode.

2022-12-20 12:31:27 Utile (0)
Soumettre
réponses (3)

Hobbyboy possibly not! you would need to check if the protocol is supported. You may need a JR style multi module like RadioMaster

2022-11-25 04:53:53 Utile (0)
Soumettre
réponses (2)

Q: Will it bind with fly sky transmiter?

demandé par BG521155425 sur 2022-11-16 04:46:48

Hobbyboy No! you will need a Elrs module. If your Transmitter has a JR style module bay, then you can but a elrs module to plug into the back.

2022-11-17 03:53:37 Utile (0)
Soumettre
réponses (1)

Hobbyboy The description doesn't say! All most all fpv cameras can change from Pal to Ntcs using the supplied tool that comes with every camera. It a joystick type deal that let's you change aspect ratio, color, little minor things.

2022-11-16 04:15:13 Utile (0)
Soumettre
réponses (1)

Hobbyboy Update so the gyro Stablized board doesn't work properly causing my bird to constantly nose in. If and when it does the controls seem stuck. The only thing that does work properly is the motor and gearbox. Plenty of power for this little guy. I tried fixing it but no change. All I did was re-adjusted the linkage to the elevator servo. That didn't work because the tail still goes down as the plane sits. It does not level out, even if you prop the tail up level and plug in battery. It looks nice but mines will not fly properly.

Hobbyboy 16/10/2022
0
Commentaires (2)

Hobbyboy I notice this also that these prices are way off. Elrs rx over $20, bit you can find them here in the States for under $15 unless it's Matek.

2022-11-06 04:13:34 Utile (0)
Soumettre
réponses (1)

Q: can These work for xk 110s?

demandé par BG521210404 sur 2022-10-28 06:06:25

Hobbyboy The Xk line of rc toys usually uses a all in one board. Which has the rx, esc and servo mounted to a single board. The servo plug is usually Jst 1.25 3p. The servo you are inquiring about has regular JR,Futaba servo head. No it will not work unless you change the plug end

2022-11-06 04:11:04 Utile (0)
Soumettre
réponses (1)

Q: can this receiver be paired to a flysky gt5?

demandé par BG482050637 sur 2022-10-30 02:06:14

Hobbyboy Yes and No! yes if you have a elrs module like Namimno or Betafpv. Plenty of modules out on the market. No if your tx doesn't have a JR style module bay. I have a RMT16 with Nanmimno module works great too

2022-11-06 04:06:19 Utile (0)
Soumettre
réponses (1)

Q: will it fit scx10 2 or what should I buy ?

demandé par BG321043524 sur 2020-09-20 11:46:29

Hobbyboy This motor is a direct replacement for a 540brushed motor. Check your specs chances are you have a 540motor and yes it will work.

2022-10-30 05:22:23 Utile (0)
Soumettre
réponses (4)