BG223118341
Q: What are the Width, Height , and Depth, as well as thickness of the materials used.
demandé par BG223118341 sur 2021-10-08 07:04:00
BG223118341 4mm would be about right and you can but it at any hardware store. Tell them it is for a chainsaw.
2021-07-05 06:28:09 Utile (0)
BG223118341 I do not believe that they sell new chains however, others do and they will fit.
2021-05-31 03:44:18 Utile (0)
Q: This product exists in a larger size, a few kg load capacity?
demandé par Chariot sur 2021-04-04 06:47:18
BG223118341 Yes it does. On Eleksmaker,s site.
2021-04-04 06:56:35 Utile (0)Q: Does anybody know how this works, can't see directions or instructions.
demandé par BG361211134 sur 2021-03-10 02:38:03
BG223118341 They have a video on how to use this product. I believe it is at the bottom of the page where the tools arew.
2021-03-10 06:57:59 Utile (1)
BG223118341 You may get away with corner brackets or end plates.
2021-02-24 06:21:19 Utile (0)
BG223118341 I can `t see why not, if your board can handle the amps and you watch orientation of the A+ A- B+ B- (red blue green black).
2021-02-12 03:17:42 Utile (0)Q: Hello, do I have a question? Is it a compatible with Atomstack A5 - 20W? Thank you for answer.
demandé par BG114252315 sur 2021-02-04 09:11:43
BG223118341 I am not an expert on Atomstack A-5, however the #17 stepper motor uses 1.3 amp to operate. You may need a 4th axis to run the elecks rotate. If the steppers on the Atomstock are #17, I do not see a problem. If the Atomstack uses 2 steppers, then you will need a board that drives 3 steppers.
2021-02-04 09:32:13 Utile (0)Q: will this rotary unit work with the neje master master 20w laser engraver?
demandé par damnnoid sur 2021-01-28 08:31:00
BG223118341 The rotation is done by the stepper motors, which get their signal from the stepper drivers. The laser is controlled on its own from the board. I hope this is of some help.
2021-01-28 09:28:20 Utile (0)Q: Can this work with the atomstack lazer engraver??
demandé par BG192254123 sur 2020-12-18 08:02:24
BG223118341 I can not say for sure, however I believe if the laser is set properly I can,t see why not. (meaning the height, focal length.)
2020-12-18 09:24:45 Utile (0)
BG223118341 Iam disappointed as the rods are too short. It would be better if you cut the aluminum profiles to match the large diameter of the rods, so the small end could fit in the bearings as they should. It would make for a better product.
2020-09-19 10:02:32 Utile (0)
Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!
Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.
Aidez les autres et soyez plus heureux!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
The seller Sliding table size：40*70mm
2021-10-08 08:33:06 Utile (0)