Tous les messages

Q: has the 5.8ghz tx module built internally?

demandé par nicoladi palma sur 2018-09-06 01:14:07

englundandy the fpv function of this camera is operated through wifi, it has very limited range. The wifi is mainly for changing camera settings and downloading recorded files. This camera is more often used for recording hd quality that the fpv cameras cannot usually deliver.

2020-12-11 01:54:30 Utile (0)
Soumettre
réponses (1)

englundandy The eachine tyro 129 is designed for 6s voltage. Any 5s battery will be acceptable voltage. The 40amp esc is a 4 and 1 so the actual amperage that esc can handle is 40amps×4= 160amps continuous or 240amps burst. You wont ever burn this esc by using a 5s battery

2020-12-11 01:51:27 Utile (0)
Soumettre
réponses (1)

Q: How I need to buy if I have a novice 3 thegogles and the receptor

demandé par Diego Tomasello sur 2020-12-03 06:37:02

englundandy If you have the eachine novice 3 these goggles will work with that kwad. These goggles will work with any 5.8ghz analog vtx(like you will find on most non digital kwads). Im not sure i understood your question though.

2020-12-03 01:29:46 Utile (0)
Soumettre
réponses (1)

Q: Does this fc have built in inverter for frsky?

demandé par Rifky Ramadhani sur 2020-11-18 02:37:35

englundandy I used an frsky r9 rx, non-inverted and had the sbus pads bridged and it worked great.

2020-12-03 01:26:43 Utile (0)
Soumettre
réponses (2)

englundandy The wifi has about a 25 meter capability. Much further than that an you will start experiencing wifi dropouts and disconnected messages. Its best to have the phone and camera right next to eachother for setting changes and downloading files.

2020-12-03 01:22:23 Utile (0)
Soumettre
réponses (1)

Q: Will it fit fatshark recon v3?

demandé par BG371336143 sur 2020-12-02 03:03:59

englundandy No definitely not. This case is designed for the lower profile binocular style of goggles. Box goggles will need a much larger case. Perhaps a small soft sided cooler, the size designed to chill a six pack.

2020-12-03 01:18:33 Utile (0)
Soumettre
réponses (2)

Q: is it disarmed from the factoryjQuery111307608580544679711_1606297085196

demandé par BG503712423 sur 2020-11-25 03:38:35

englundandy Yes it comes disarmed, it will only arm with the switches set up to arm. Verify correct switch operation before plugging in battery. This drone is not a toy, the props will cut off fingers if your not careful.

2020-11-25 08:41:36 Utile (0)
Soumettre
réponses (1)

Q: Theres no way to put a DJI air unit on this huh?

demandé par BG465723852 sur 2020-09-28 10:48:04

englundandy Usually people don't put a dji air unit in such a budget kwad. There would be room however, mount it on above the top plate and the GPS mounted on an arm, or a 3d printed mount on the rear. Part of this hobby is making things work, things that wouldn't normally work together.

2020-09-28 11:04:26 Utile (0)
Soumettre
réponses (4)

englundandy An external current sensor may be needed, or if it is equipped with a current sensor already than it needs to be calibrated.

2020-09-09 09:11:33 Utile (0)
Soumettre
réponses (6)

englundandy some 3d printed mounts will have enough room to fit this camera. The newer runcam 5 orange fits the all the session 4 or 5 mounts. brain3d sells a perfect printed mount for this camera.

2020-09-07 01:08:08 Utile (0)
Soumettre
réponses (1)

Q: is this drone ligal in israel?

demandé par mizrachishai sur 2020-02-28 04:12:35

englundandy Probably not, terrorists don't need any more ideas.

2020-08-25 12:34:41 Utile (0)
Soumettre
réponses (3)

englundandy Yes your new drone will need to be registered with the FAA. New York may have additional laws about where no fly zones are located. New York is pretty uppity about anybody doing anything so check local laws before any flights.

2020-08-25 12:33:45 Utile (0)
Soumettre
réponses (5)

englundandy Hmmmm....machine does make counter clockwise and clockwise threaded shafts on there motors. Identify that the correct nut is being used on the correctly threaded shaft. You may have a cross threaded motor shaft that will need to be threaded or replaced. HOPE THIS HELPS

2020-08-25 12:31:30 Utile (0)
Soumettre
réponses (2)

englundandy A 5s or 6s would work the best. 2507 with 7" props will pull alot of amps. A 2200mah 5s or a 1500mah 6s would be perfect. A 2200mah 5s will get you 15 minutes of flight time and a 1500mah 6s will get about 10 minutes of flight time.

2020-08-25 12:28:22 Utile (0)
Soumettre
réponses (6)

englundandy The transmitter takes 4 AA batteries. Its flysky protocol so it uses ibus. D8 and d16 are frsky protocols.

2020-08-25 12:24:19 Utile (0)
Soumettre
réponses (1)

Q: What Google's do you recommend

demandé par BG401044834 sur 2020-04-21 01:38:39

englundandy skyzone 02c are excellent. avoid the eachine ev100. the fov is super tiny.

2020-04-21 05:41:56 Utile (0)
Soumettre
réponses (6)

Q: what viewer is compatible with???

demandé par BG181544334 sur 2020-03-08 08:08:21

englundandy any 5.8ghz goggles or monitor will work with this kwad. i recommend skyzone goggles personally.

2020-03-09 05:47:34 Utile (0)
Soumettre
réponses (1)