robertcasperuk
mon contenu
Tous les messages
Commentaires
Commentaires
réponses
Questions

Tous les messages

robertcasperuk 29/10/2021
Excellent. Silent as described. Ordering another 3
Silencieux DIY Quartz Mouvement Horloge Mécanisme Mute Mains Réparation Outil Pièces Kit
7,45€ 8,29€
0
Recommandations
Commentaires (0)
robertcasperuk 21/10/2021
ER25 straight shank collet holder: Nicely made. Clocked it for runout. All good. Great price for a quality piece
ER11 à ER25 Porte-mandrin à tige droite C8 à C20 Outil de tour de fraisage CNC
15,97€ 16,60€
0
Recommandations
Commentaires (0)
robertcasperuk 05/06/2020
Firstly, this arrived in good time. On first look it is nicely made. The nut thread is clean and smooth. The shaft diameter is 0.005 mm undersized so 10 mm bearings fit easily, but I will test the run-out under axial load to see how that turns out, which I shall report when I have tested it. The run-out is advertised at .01 mm and again I will report later when I have done testing it. I have given this spindle 5 stars but will change that if the run-out is not as stated. For the price paid with delivery this is excellent value.
Porte-pince C10 ER11A 100L pour fraiseuse CNC, tige d'extension de 100 mm avec queue droite
13,84€ 14,75€
0
Recommandations
Commentaires (0)
robertcasperuk 05/06/2020
Firstly, the spindle arrived in good time. I bought a couple of these from different vendors to compare the quality. This one is the slightly more expensive of the two, but still very cheap. On first look I notice that the nut thread is rough. I have done quite a bit of threading on an industrial scale and can see immediately on this one I received the threads are tearing along the apex; before they get to this state the threading cutters should be changed for new ones. Having said that, the nut does close OK on the collets. Next. The shaft is .01 mm undersized which means it has no trouble receiving a bearing - but this will not help with the claimed run-out of .003 mm especially where significant axial load applied, but I will test that and report back later. The other cheaper one I received from a different supplier is designated .01 mm run-out. The shaft on that one is only .005 undersized and the nut-thread on the shaft is nicely cut with no tearing at all. It will be interesting to compare the run-out on each of these, so I will update later. I have only given 3 stars on the quality because of the poor spindle thread and the 100th mm undersized shaft diameter. If the run-out turns out be as stated I will increase the quality to 4. Either way this spindle is excellent value for the price paid including delivery.
C10 er11a 100l pince extension de support de mandrin tige droite pour le fraisage CNC
21,30€ 22,13€
0
Recommandations
Commentaires (0)
robertcasperuk 28/05/2020
Arrived yesterday after 1 month; not well packed but not damaged.. Seems decent. Grooved at one end to take a cir-clip and threaded M14 x 1 at the other end which is useful albeit a little rough. I ordered this to check out the quality and delivery - so far so good. Later I will test its accuracy and machining properties add a review on that. I loaded it to a 12 mm collet on the thread end to check run-out. Bang on!
Vis à billes 250 mm SFU1605 Vis à billes avec écrou à billes unique pour CNC
37,28€ 38,74€
0
Recommandations
Commentaires (1)

Vous êtes l'expert, pouvez-vous aider?

Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!

Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.

Aidez les autres et soyez plus heureux!

  • S'abonner

À propos des badges

Les badges sont liés à la communauté et les utilisateurs le font en créant un contenu de qualité, en complétant des missions ou en participant à des activités spéciales. Les personnes spécifiques auront également leur propre badge exclusif.
Badge du PDG

L’insigne du PDG appartient uniquement au patron de Banggood.

Les badges que vous pouvez gagner arrivent bientôt
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe