Meilleures offres pour Testeur de courbe VI,4Pcs Astrolux® C1830 3000mAh batterie 18650,Capteur de Hall - Banggood France Achats en ligne

Grandpa

mon contenu: Tous les messages; Commentaires; Commentaires; réponses; Questions

Tous les messages

Grandpa 25/08/2022

I was a bit unhappy at first as I was not able to download the manual and my unit arrived with a cracked case. I began to investigate it and repair it. The instructions available on the sales page provided enough information to set the unit up and running some tests. The unit works better than I had expected. I was able to determine the frequencies used. Low = 62 Hz Med = 234 Hz Med 2 = 2 kHz and High = 14.5 kHz. The red knob selects one of 4 different internal resistances. The A/B push button turns on and off the dual channel mode so that you can easily compare one circuit board position to another. The Blue knob adjusts the position of the "B" Channel image on the scope screen. I added a power switch to the unit so that it could be left plugged in when I wanted to. I also added some English Labels and non-slip feet for the back so that it doesn't slide around on the bench. The only item I have not been able to identify is a Blue Jack on the front that is labeled "G" on the front and "T" on the internal board. If anyone has figured what the "G" Jack is please let me know. I wrote a complaint to Banggood about the inability to down load the Manual and about a week later they sent me the pdf file. Unfortunately it did not identify the "G" jack. Over All I am very pleased with the unit and the way it functions. I would recommend it to anyone who has a curiosity about curve tracers and a scope capable of X-Y operation.

Testeur de courbes VI double canal, affichant 2 formes d'onde simultanément pour une comparaison facile

32,56€ 42,79€

4

Commentaires (2)

Grandpa 01/07/2022

I was very satisfied with these batteries. Unlike many brands the Nominal rating of 3000 mAhr was accurate. When I ran a power test I got a reading of 2920 mAhr. The batteries also weigh a little more than many of the batteries that are being sold. The batteries from this order were about 46 gm. I felt it was a very good buy and I will buy more in the near future.

4Pcs Astrolux® C1830 3000mAh 3.7V 18650 Batterie lithium rechargeable Li-ion non protégée Cellule d'alimentation 9.6A haute performance pour lampes de poche Nitecore Lumintop Fenix Olight Jouets RC

26,74€ 27,90€

0

Commentaires (0)

Grandpa 29/07/2020

3pcs Capteur Hall LM393 3144 Module de Capteur Hall pour Smart Car Geekcreit pour Arduino - produits compatibles avec les cartes Arduino officielles

6,44€ 7,43€

0

Commentaires (0)

Grandpa 29/07/2020

Kit de dés électroniques avec protection de connexion inverse LED pièces électroniques bricolage

7,51€ 8,36€

0

Commentaires (0)

Grandpa 29/07/2020

Bricolage NE555 Ding Dong Bell Kit de module de sonnette DIY Music Kit de formation à la production électronique DIY

6,44€ 2,78€

0

Commentaires (0)

Grandpa 29/07/2020

Infrarouge Parking Capteur Kit Infrarouge Inverser La Vitesse Rappel Électronique PCB Circuit Board Production DIY Kit

8,59€ 9,30€

0

Commentaires (0)

Grandpa 29/07/2020

If you have purchased this kit to test or improve your soldering skills do not be too hard on yourself. The traces on the circuit board are very fragile. I have years and thousands of hours of soldering experience and I had to repair 4 traces that broke while the unit was being assembled. The slightest torque on any of the components or LEDs causes the trace to lift from the board and break. Use a continuity meter to test your traces if the unit doesn't work and then use clipped leads to jumper across the breaks in the traces. You can't beat the price so forgive yourself on this one if it does't work right out of the gate. Also be aware that CCW on the trimmer increases sensitivity and CW decreases the sensitivity.

LM3915 Kit d'indicateur de niveau audio à 10 segments, expérience de formation en soudage électronique, pièces de bricolage

3,71€ 4,18€

0

Commentaires (0)

Grandpa 29/07/2020

Kit de 3 dés électroniques avec protection de connexion inversée, dés à LED à faire soi-même, pièces électroniques

10,75€ 6,98€

0

Commentaires (0)

Grandpa 29/07/2020

Diy touch vibration alarme kit formation électronique enseignement

2,78€ 3,71€

0

Commentaires (0)

Grandpa 07/02/2020

I am quite pleased with this power supply control board except for one problem. The circuit is designed to use (3) TL081 Op Amps which have an Offset circuit built in. The Offset is necessary in the U2 position (lower right hand corner above the blue trimmer) if you want to bring your voltage to zero volts when the voltage control is all the way down. Unfortunately the TL081 chips that are currently being supplied with the kit are not quality and they do not have the Offset circuitry built into the chip. If you want to be able to zero your voltage output when the voltage control is all the way down you will have to purchase a quality TL081 chip for this position. At the price they are selling these kits for this is a small problem and easily remedied. John

Module d'alimentation régulée réglable de 0-30V 2mA - 3A DIY Kit

7,43€ 8,92€

0

Commentaires (0)

Grandpa 23/01/2019

I have ordered these M-Testers a couple times and I have generally had good luck with them. The plastic cases make them a lot more usable and attractive. This batch however had one unit that didn't work properly. Looks like the Atmel chip is defective but at the cost per unit it is no problem.. I will use it for spare parts. A second problem with each unit seemed more serious. The test socket contacts would not open all the way. After removing the sockets from the board and checking them out I found that they worked just fine once they were removed from the board. The source of the problem was that the sockets had been soldered to the board by the manufacturer while in the closed position. This holds the contacts to one side and when the socket is soldered the solder holds the pins towards the closed side and doesn't allow them to open. The solution if you are having this problem is to simply open the test socket and heat up the solder to each pin to allow the pin to come to its normal open position. John

Geekcreit® LCR-T4 Mega328 Testeur de transistor Diode Triode Capacité Mètre ESR Avec coquille

13,42€ 20,46€

0

Commentaires (1)

Grandpa 15/10/2018

These buttons are momentary, not latching! The information supplied is contradictory as it states both latching and momentary. They are also small like the typical small key switch with an LED under the button.

Interrupteur de verrouillage du symbole d'alimentation LED Bouton poussoir lumineux SPST

7,48€ 8,36€

0

Commentaires (0)

Grandpa 27/09/2018

This is a normally open momentary switch.

Wendao R13-507 125 V 6A 16 mm sans verrouillage interrupteur à réinitialisation automatique bouton poussoir ÉTEINT ALLUMÉ 10 pièces

15,04€ 15,81€

0

Commentaires (0)

Grandpa 26/07/2018

I was a little surprised by how small the cutters were, only 3.75 inches from pointed tip to end of handle but they cut very well and were well machined. I was able to cut typical leads at the very tip of the jaws with no problems. The small size may even be an advantage. John

Pinces diagonales de DANIU Mini - Pinces à dénuder - Coupe-fils électriques

3,84€ 9,30€

0

Commentaires (0)

Grandpa Sorry I missed your question earlier. 24cm wide X 9 cm high X 26 cm deep with approx 4 kg.John

Grandpa 29/08/2017

This is a very versatile and useful basic power supply circuit. So far I have used it to build several dual bench power supplies and other specialized test equipment. Lots of fun.

Module d'alimentation régulée réglable de 0-30V 2mA - 3A DIY Kit

7,43€ 8,92€

7

Commentaires (2)

Grandpa 11/04/2018

I think this is the nicest little meter I have ever owned. It has features and accuracy found on meters 10 to 20 times more expensive. It even has an EM field detector so you can tell when a conductor is hot with lethal voltage. The only problem I had is that one of the internal fuses had popped out of its clips during shipping so I had to open the case and put it back in place. John

MUSTOOL MT66 Vrai RMS 5999 Compte Multimètre Numérique AC / DC Testeur de Tension

20,60€ 22,48€

0

Commentaires (0)

Grandpa 21/03/2018

I bought 5 of these and they are working great. My 11 year old grandson built one the other day and it turned out good after we discovered he had switched one 8550 with an 8050. It is nice when a mistake like this doesn't cause anything to burn up. After putting things where they belonged it worked well. We mounted it on a 6 volt battery box with a power switch and he had a nice little project to show at school.

5Pcs Electronic DI DIY Kit 5mm Rouge LED Pièces intéressantes NE555 CD4017 Electronic Production Suite

15,04€ 15,81€

0

Commentaires (0)

Grandpa 21/03/2018

As noted by other reviewers the circuit doesn't work well as designed but I do not agree with them as to how to fix it. R-2 39K has the purpose of introducing hysteresis into the circuit, however it creates way too much and extreme temperature moves are necessary to make it work. Just changing R2 from 39K to 100K brings the hysteresis down to 4 degrees C. The LED should have a current limiting resistor and there is a problem with Q1 overheating if the transistor is turned on to saturation by the variable resistor. Keep the variable resistor away from the 0 ohms end of its travel. This circuit was a lot of fun since it didn't work and took some study and experiment to make it function. For the price I had a lot of fun.

Kit de contrôle de la lumière du son de contrôle de température DC3-5V Electronic Circuit DIY Training Suite

2

Commentaires (1)