Avis sur Kit Geekcreit® de grande taille avec contrôle tactile de l'égaliseur numérique à LED de 225 segments pour le spectre musical des ondes sonores

Kit Geekcreit® de grande taille avec contrôle tactile de l'égaliseur numérique à LED de 225 segments pour le spectre musical des ondes sonores

17,33€
~~18,44€~~
Acheter maintenant

Avis des clients

4.61 sur 5

Voir tous les 138 commentaires

5 étoile
117 (84.8%)
4 étoile
7 (5.1%)
3 étoile
3 (2.2%)
2 étoile
3 (2.2%)
1 étoile
8 (5.8%)

Ecrire un commentaire Obtenez le double des points de revue si vous votre revue est l'une des 3 premières publiées !

Tous les Commentaires (138)
Image (17)
Vidéo (1)
Toutes les Étoiles
- Toutes les Étoiles(138)
- 5 Étoile(117)
- 4 Étoile(7)
- 3 Étoile(3)
- 2 Étoile(3)
- 1 Étoile(8)

Trier par:

Commentaire Top

Commentaire Top
Le plus utile
Le plus récent

Avis uniquement de votre pays (France)

Afficher l'original

Une partie de la critique a été traduite automatiquement.

AlferekVIP3
PL
03/05/2017

This product is not easy to solder. 225 LEDs, each 3 times (including soldering the cathode pad). Good advice is to check the each LED column separately using 2,5V voltage, before soldering MCU. Checking earlier soldering of each LED can exclude bad connection. Please check voltages: Pin at C1 is the ground. The same ground is the pin 14 of MCU. Pin 12 od MCU is +5V. Other pins on MCU should have a little lower voltage (about 4,8V). After a few times of checking my soldering this product works and was worth to buy.

This product is not easy to solder. 225 LEDs, each 3 times (including soldering the cathode pad). Good advice is to check the each LED column separately using 2,5V voltage, before soldering MCU. Checking earlier soldering of each LED can exclude bad connection. Please check voltages: Pin at C1 is the ground. The same ground is the pin 14 of MCU. Pin 12 od MCU is +5V. Other pins on MCU should have a little lower voltage (about 4,8V). After a few times of checking my soldering this product works and was worth to buy.

This product is not easy to solder. 225 LEDs, each 3 times (including soldering the cathode pad). Good advice is to check the each LED column separately using 2,5V voltage, before soldering MCU. Checking earlier soldering of each LED can exclude bad connection. Please check voltages: Pin at C1 is the ground. The same ground is the pin 14 of MCU. Pin 12 od MCU is +5V. Other pins on MCU should have a little lower voltage (about 4,8V). After a few times of checking my soldering this product works and was worth to buy.
14

Commentaires

Afficher l'original
montargoVIP2
MX
05/04/2019

llego más pronto de lo esperado excelente vendedor y el artículo bastante interesante nada más ay que tener paciencia para armarlo gracias a banggood

llego más pronto de lo esperado excelente vendedor y el artículo bastante interesante nada más ay que tener paciencia para armarlo gracias a banggood

llego más pronto de lo esperado excelente vendedor y el artículo bastante interesante nada más ay que tener paciencia para armarlo gracias a banggood
1

Commentaires

Afficher l'original