reçu comme décrit. bon vendeur.

received as described. good seller.

reçu comme décrit. bon vendeur.

Not for the faint hearted. Yes, it requires soldering of SMD components. This item is more work than the smaller flat rotaters because you need to solder 4 24 pin SMD chips.It is definitely easier than the spheric rotator in which you must also solder the little LED's at the side of a PCB. It is not clear from the description that this model runs on 12V. But it is mentioned on the PCB and in the schematic. Testing can be done on 5V, because it will rotate, and the LED's will light up. But the turning is off. I have yet to find out how to set the clock. One person mentioned that the 1.5K resistors are missing. Yes, but a set of 2.2K resistors are provided instead. Use these. There are NO spare LED's, so be careful not to loose even one. I ordered the blue kit, which has a red LED on the most outwards position. But that LED is not supplied. I took one from my box with spares. Be careful with the LED receiver. Follow the manual as you have not to follow the direction on the PCB. This is mentioned on several places. For the DC female connector you must disobey the manual as it is wrong at that point. Ignore the middle connector. I blew the U4 chip, with the result that LED 5 will not light up. I might repair that later on. Otherwise: a decent kit, but certainly a bit expensive. Oh, and I have not been busy with the reprogramming. All is in Chinese. I have to subtract points for that one. Their appear to be only 3 pre-loaded pictures. Value for price: too expensive, costs 2 points. Quality: for the exchanged resistors, missing outer LED, lack of description on how to set the clock, costs 2 points Appearance: lack of english description on how to replace the code: costs 1 point.

Not for the faint hearted. Yes, it requires soldering of SMD components. This item is more work than the smaller flat rotaters because you need to solder 4 24 pin SMD chips.It is definitely easier than the spheric rotator in which you must also solder the little LED's at the side of a PCB. It is not clear from the description that this model runs on 12V. But it is mentioned on the PCB and in the schematic. Testing can be done on 5V, because it will rotate, and the LED's will light up. But the turning is off. I have yet to find out how to set the clock. One person mentioned that the 1.5K resistors are missing. Yes, but a set of 2.2K resistors are provided instead. Use these. There are NO spare LED's, so be careful not to loose even one. I ordered the blue kit, which has a red LED on the most outwards position. But that LED is not supplied. I took one from my box with spares. Be careful with the LED receiver. Follow the manual as you have not to follow the direction on the PCB. This is mentioned on several places. For the DC female connector you must disobey the manual as it is wrong at that point. Ignore the middle connector. I blew the U4 chip, with the result that LED 5 will not light up. I might repair that later on. Otherwise: a decent kit, but certainly a bit expensive. Oh, and I have not been busy with the reprogramming. All is in Chinese. I have to subtract points for that one. Their appear to be only 3 pre-loaded pictures. Value for price: too expensive, costs 2 points. Quality: for the exchanged resistors, missing outer LED, lack of description on how to set the clock, costs 2 points Appearance: lack of english description on how to replace the code: costs 1 point.

Not for the faint hearted. Yes, it requires soldering of SMD components. This item is more work than the smaller flat rotaters because you need to solder 4 24 pin SMD chips.It is definitely easier than the spheric rotator in which you must also solder the little LED's at the side of a PCB. It is not clear from the description that this model runs on 12V. But it is mentioned on the PCB and in the schematic. Testing can be done on 5V, because it will rotate, and the LED's will light up. But the turning is off. I have yet to find out how to set the clock. One person mentioned that the 1.5K resistors are missing. Yes, but a set of 2.2K resistors are provided instead. Use these. There are NO spare LED's, so be careful not to loose even one. I ordered the blue kit, which has a red LED on the most outwards position. But that LED is not supplied. I took one from my box with spares. Be careful with the LED receiver. Follow the manual as you have not to follow the direction on the PCB. This is mentioned on several places. For the DC female connector you must disobey the manual as it is wrong at that point. Ignore the middle connector. I blew the U4 chip, with the result that LED 5 will not light up. I might repair that later on. Otherwise: a decent kit, but certainly a bit expensive. Oh, and I have not been busy with the reprogramming. All is in Chinese. I have to subtract points for that one. Their appear to be only 3 pre-loaded pictures. Value for price: too expensive, costs 2 points. Quality: for the exchanged resistors, missing outer LED, lack of description on how to set the clock, costs 2 points Appearance: lack of english description on how to replace the code: costs 1 point.

good, fun project. :)

good, fun project. :)

good, fun project. :)

semble bon tout est arrivé ok. pas encore construit

looks good all arrived ok. not built yet

semble bon tout est arrivé ok. pas encore construit

J'attends toujours une réponse sur ce qu'il faut faire avec le spectacle parce que la carte mère est défectueuse.

Ich warte immer noch auf eine Antwort,was mit der Sendung passieren soll, da die Hauptplatine fehlerhaft ist.

J'attends toujours une réponse sur ce qu'il faut faire avec le spectacle parce que la carte mère est défectueuse.

Merci pour ma commande

Thank you for my order

Merci pour ma commande

Très bien emballé et intact est arrivé à moi. Je vous recommanderai. Merci

Sehr gut verpackt und unbeschädigt bei mir angekommen. Werde Sie weiterempfehlen. Danke

Très bien emballé et intact est arrivé à moi. Je vous recommanderai. Merci

nice

nice

nice

very nice

very nice

very nice

i tried and failed (probably because of my fault). i will recomend this only for experienced electricians. you gona be soldering components smaller than 1mm.

i tried and failed (probably because of my fault). i will recomend this only for experienced electricians. you gona be soldering components smaller than 1mm.

i tried and failed (probably because of my fault). i will recomend this only for experienced electricians. you gona be soldering components smaller than 1mm.