Bien emballé, reçu en bon état et délai de livraison raisonnable (19 jours calendaires à partir de la commande). Le câblage est un peu étrange parce que le poussoir n'est pas connecté correctement, mais c'est un mod facile à fixer. Ça marche bien une fois que c'est fait.

Well packaged, received in good condition and reasonable delivery time (19 calendar days from order). The wiring is a bit strange because the push switch is not connected correctly, but it's an easy mod to fix it. It works well once that's done.

Bien emballé, reçu en bon état et délai de livraison raisonnable (19 jours calendaires à partir de la commande). Le câblage est un peu étrange parce que le poussoir n'est pas connecté correctement, mais c'est un mod facile à fixer. Ça marche bien une fois que c'est fait.

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

Good condition arrived in safe and all parts is ok! Good value/quality ratio. Thank you! :)

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

The encoder is OK, but the switch is NOT brought out to any pins, which means soldering, no matter what you do. Since the 'C' pin is directly connected to the GND pin, you can cut the trace on the back between the two pins, and wire one side of the switch to the old GND pin, and then wire the other side of the switch to either 'C' (the new GND pin) or to VCC. Normally you'll want the switch to GND as most micros have internal pull-up resistors, and it's less to wire in later. I've added a schematic of the debounce filtering on the photos below for your convenience. If you still have too much bounce, you might want to add up to .1uF caps on top of the existing 22nF capacitors. You may not need it. Since the description doesn't mention it, the encoder has 20 detents / positions per 360 revolution. I can't do a PREVIEW, so hopefully the photo comes through readable.

Très heureux avec cet article!

Very happy with this item!

Très heureux avec cet article!

Exactement ou que je voulais

exactamente o que pretendia

Exactement ou que je voulais

Comme décrit. Arrivé dans un délai raisonnable.

As described. Arrived in reasonable time.

Comme décrit. Arrivé dans un délai raisonnable.

D'accord

ok

D'accord

D'ACCORD

OK

D'ACCORD

Excellent composant, facile à utiliser avec Arduino.

Excellent component, easy to use with Arduino.

Excellent composant, facile à utiliser avec Arduino.

On ne peut pas se tromper avec ça.

Can't go wrong with these

On ne peut pas se tromper avec ça.