AresFPV
Q: does this Rx work with low voltage servo? If the input vikty is 1S lipo (3.7v-4.2v)
demandé par KLKOK sur 2018-09-12 01:18:40
AresFPV yes should work fine but as you said it will need a power input
2023-01-07 02:10:04 Utile (0)Q: Is this DSMX/DSM2 compatible?
demandé par gjadam1 sur 2021-05-02 02:24:15
AresFPV no it is not. it uses the afhds 2a protocol
2023-01-07 02:09:24 Utile (0)Q: can this be used in EU (italy) ?
demandé par Yexel sur 2018-01-04 06:58:52
AresFPV should be ok as its a 2.4ghz system
2023-01-07 02:06:36 Utile (0)Q: what is working distance between receiver and remote control
demandé par BG539185151 sur 2021-11-18 02:20:28
AresFPV average around 400m maximum I expect
2022-11-05 11:46:34 Utile (0)Q: Can this be used in the uk? The nominal voltage here is 230v
demandé par BG564816174 sur 2020-04-17 07:09:06
AresFPV yes the power supply is configured for 230v
2022-11-05 11:45:28 Utile (0)Q: can it get stuck at customs in India???
demandé par Chaitany sur 2020-04-08 12:31:00
AresFPV not sure. may be best to contact BG directly
2022-07-22 04:19:28 Utile (0)Q: Can I use the bn-880 with that mount?
demandé par M0CKY sur 2020-06-22 09:08:43
AresFPV I think the 880 is a bit too large, the antenna would not fit with the lip around the mount. it may be possible for it to fit with slight modification to the mount, but this gps module is just slightly larger
2022-07-22 04:18:45 Utile (0)
AresFPV you need to print a replacement z carriage, have a look at this one on thingiverse: thing:4803721
2022-07-05 04:17:49 Utile (0)Q: i have bond with my flysky fs i6 but the Signal com not i don't know why can you please help me
demandé par Mojaa sur 2018-10-27 03:31:41
AresFPV it could be you have selected the wrong communication method, this should be pwm for this receiver, that or it did not bind correctly. having a correct binding should show the voltage of the receiver on the transmitters screen
2022-07-05 04:14:29 Utile (0)Q: does this have a receiver built into it?
demandé par Kevin sur 2019-10-18 10:51:54
AresFPV no you will need one separately
2022-06-22 03:00:40 Utile (0)
AresFPV yes. i suggest using single flute endmill for ali
2022-06-22 03:00:05 Utile (0)Q: Can this Rx FS2A be binded with a Turnigy 9X V2 AFDHS2A ?
demandé par claudycharlier sur 2020-12-05 10:03:08
AresFPV yes the 9xv2 with the afhds2a module will bind as the protocols are the same
2022-05-29 11:26:50 Utile (0)Q: Is there a wiring diagram available?
demandé par kechols_jr sur 2020-04-22 03:19:04
AresFPV fairly simple to wire, power is positive to the fused side i believe, motor doesnt matter as the wires can easily be swapped if the motor spins the wrong way. switch is used to turn on or off the motor separately or through a control board.
2022-05-29 11:13:47 Utile (0)Q: How do I power up the unit? It is DC right? Difficult to find a DC power converter with 30 Volts
demandé par flowin_through sur 2021-04-07 10:14:27
AresFPV the power supply is connected to mains AC. there is no earth connection, but you can add one to the motor and or the power supply for safety
2022-05-29 11:11:03 Utile (0)
AresFPV may be best contacting BG
2022-05-20 01:46:39 Utile (0)Q: It is for two-pole motor or for three-pole motor?
demandé par Pablo_Razo sur 2019-11-14 04:01:58
AresFPV brushed esc, so brushed or two pole motor
2022-05-17 08:33:18 Utile (0)Q: Will it work with Turnigy TGY-i6?
demandé par russell sur 2017-11-04 08:56:44
AresFPV yes as protocols match also should work with i6s
2022-05-17 08:32:43 Utile (0)Q: peux t'on l'alimenter en 6S?
demandé par pad sur 2019-10-19 05:03:30
AresFPV works with 6s, you need a large 50v 1000uf capacitor, and you will have no issues
2022-04-28 02:59:54 Utile (0)Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!
Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.
Aidez les autres et soyez plus heureux!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
