Kris
mon contenu
Tous les messages
Commentaires
Commentaires
réponses
Questions

Tous les messages

Kris 27/10/2023
Overall a decent fence, however, there are a couple of material issues as well as design issues. 1. Fence stops pieces are made of aluminium base and plastic composite stop piece. The bolt-washer combo which holds the stop piece is undersized for this stop. As a result, it bends easily even with not much force. This is a bad design in combination of a poor choice of materials. 2. The fence micro adjusters are badly designed (too small) and also they cheaped out on the connection design which is done by a bolt-plastic slot combination. It works, but it is not convienient to use and the slack in the connection is huge. I chose not to use it at all. 3. The big stop bolt system has an aluminium turn head but base is plastic. Works, but have to be careful not to break it by tightening the bolt with too much force. Aluminium base part should have been used instead.
ENJOYWOOD Wnew Table de fraisage en bois avec système de clôture en profilé d'aluminium de 700mm avec supports coulissants et protection de la fraise
167,47€ 372,17€
1
Recommandations
Commentaires (1)
Kris 09/11/2023
Quality control of packaging is bad. I ordered 12 tracks. 1 out of 12 came in without being properly packed with missing screws and end damaged because of missing the wrap package. I would give this a 3-star rating, but they would filter it out.
1 Pc 800mm T-slot T-tracks Outil de fixation pour table de routeur
18,60€ 17,67€
0
Recommandations
Commentaires (1)
Kris 07/11/2023
The quality is acceptable. The packaging was a bit sloppy. Whoever packed this thing did put the loose steel bolts with a same slot with the miter gauge and it got some cosmetic damage. Otherwise its OK. The only problem I have with its functionality is that the right side is 90 degrees. That means it cant do 45 deg cuts without offseting. This can be annoying for many. I would have preffered it to be 45 deg.
Biseau HONGDUI HD-MG21 avec clôture étendue pour scie à table et table de routeur pour menuiserie réglage d'angle de précision
236,33€ 372,17€
0
Recommandations
Commentaires (1)
Kris 27/10/2023
Good tool. Quality as expected. Keeps its 90degree angle when tightened.
Équerre combinée réglable en alliage d'aluminium de 300 mm Drillpro, angle de 45 et 90 degrés, pointe de compas en acier, règle en acier pour menuiserie, outil de mesure bricolage pour charpentier
10,23€ 24,18€
0
Recommandations
Commentaires (0)
Kris 27/10/2023
Good tool. Quality as expected. I little pricy, but well worth it.
Rabot à chanfreiner pour le travail du bois HONGDUI avec 3 inserts remplaçables en carbure, double lame de coupe de coin pour une coupe rapide des bords du bois
61,40€ 93,04€
0
Recommandations
Commentaires (0)
Kris 27/10/2023
Good tool. Quality as expected for the price.
Nouvelle scie à table 3D Bloc d'alimentation en bois Bloque de poussée de sécurité pour scie à table
65,12€ 74,43€
0
Recommandations
Commentaires (0)
Kris 26/10/2023
The price is a bit much, but the product is well made. A couple of issues when assembling. a. for some wierd reason a 10mm wrench was included. That was useless, since there is no 10mm bolts or nuts on this thing. Intead there should have been a PH3 screwdriver. b. One steel slider insert had a very bad thread and I was forced to make a new one for it. Luckily I had a right tools for it. I calibrated by making an actual cut and adjusted brackets according to the real outcome. This is a better way to get accurate calibration. When in full lenght the tool was off by 1mm at 1200mm mark. So I had to sand two outer pieces a little shorter to make it fully accurate. When all that was done, everything worked fine and the cuts were up to 0.3mm accurate for all lengths. Overall I am happy with it.
Système de guide parallèle en alliage d'aluminium amélioré ENJOYWOOD pour des coupes répétables pour rail de scie circulaire adapté aux outils de menuiserie Makita et Festool. Mise à niveau du crochet
120,95€ 186,08€
0
Recommandations
Commentaires (1)
Stack Geprc Stable Pro F7 avec double gyroscope Contrôleur de vol de 20x20mm et ESC 4in1 BLheli_32 de 35A et VTX 5,8G de 500mW pour drones de course RC FPV
151,43€ 139,57€

Q: The length of the m2 bolts?

demandé par Kris sur 2019-08-05 02:07:04

Alvaro Navarro puedes hablar en espanyol?

2020-02-19 12:19:56 Utile (0)
Soumettre
réponses (1)
Kris 25/07/2019
Fine props. 0.4g and work well
Happymodel Sailfly-X Spare Part 6 Pairs Hélice à 2 lames de 65 mm avec trou de montage de 1,5 mm pour drone RC
8,59€ 9,30€
0
Recommandations
Commentaires (0)
iFlight SucceX mini F7 TwinG V3 F722 Contrôleur de vol & 35A 2-6S DSHOT1200 ESC & pit / 25/100/200/500 VTX
86,24€ 94,88€

Q: The length of the m2 bolts?

demandé par Kris sur 2019-08-05 02:07:15

tiemfpv about 20mm

2019-08-14 10:21:35 Utile (0)
Soumettre
réponses (1)
Kris 25/07/2019
Works as advertised.
Runcam Racer Nano CMOS 700TVL 1.8mm / 2.1mm Super WDR plus petite caméra FPV Contrôle de geste de latence faible 6 ms OSD intégré pour le drone de course FPV
33,37€ 35,72€
0
Recommandations
Commentaires (0)

Vous êtes l'expert, pouvez-vous aider?

Nous vous invitons sincèrement à vous abonner à l'e-mail d'invitation à répondre!

Si vous vous abonnez, nous vous inviterons par e-mail à répondre aux questions des gens sur les produits. En vous abonnant, vous gagnerez également le «Badge utile»! Vous pouvez vous désinscrire à tout moment sur la page des paramètres de confidentialité.

Aidez les autres et soyez plus heureux!

  • S'abonner

À propos des badges

Les badges sont liés à la communauté et les utilisateurs le font en créant un contenu de qualité, en complétant des missions ou en participant à des activités spéciales. Les personnes spécifiques auront également leur propre badge exclusif.
Badge du PDG

L’insigne du PDG appartient uniquement au patron de Banggood.

Les badges que vous pouvez gagner arrivent bientôt
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe