This is some quality kit. The box itself it came in is very sturdy and the parts fit well in the box without any movement. (We've all had a box from china at some point flattened, crushing some crucial component amirite?) The foam is light yet tuff & sturdy. And it has all the canals for wiring already layed out. There are slots in the wings for a transmitter and receiver and the kit contains carbon covers to cover them up. The manual is in almost perfect English and is good to follow. A generous amount of stickers is also supplied to get the red stripes as shown on the example photo's. The kit contains a lot of quality carbon parts. The spars are really thick comparing to the plane itself. It looks like it could take a beating. Two main spars, each elevon has a spar and two more spars (L+R) along the leading edge of the plane. This plane constructionwise, is not for beginners. You'll need to cut away some molding residue and the supplied PCB needs a good soldering hand (It's a BEC to power the servo's) Although i'm raving about the good quality, it might look like one wing half is slightly warped. I'll have to look into that. Can't wait to try this one out :D

This is some quality kit. The box itself it came in is very sturdy and the parts fit well in the box without any movement. (We've all had a box from china at some point flattened, crushing some crucial component amirite?) The foam is light yet tuff & sturdy. And it has all the canals for wiring already layed out. There are slots in the wings for a transmitter and receiver and the kit contains carbon covers to cover them up. The manual is in almost perfect English and is good to follow. A generous amount of stickers is also supplied to get the red stripes as shown on the example photo's. The kit contains a lot of quality carbon parts. The spars are really thick comparing to the plane itself. It looks like it could take a beating. Two main spars, each elevon has a spar and two more spars (L+R) along the leading edge of the plane. This plane constructionwise, is not for beginners. You'll need to cut away some molding residue and the supplied PCB needs a good soldering hand (It's a BEC to power the servo's) Although i'm raving about the good quality, it might look like one wing half is slightly warped. I'll have to look into that. Can't wait to try this one out :D

This is some quality kit. The box itself it came in is very sturdy and the parts fit well in the box without any movement. (We've all had a box from china at some point flattened, crushing some crucial component amirite?) The foam is light yet tuff & sturdy. And it has all the canals for wiring already layed out. There are slots in the wings for a transmitter and receiver and the kit contains carbon covers to cover them up. The manual is in almost perfect English and is good to follow. A generous amount of stickers is also supplied to get the red stripes as shown on the example photo's. The kit contains a lot of quality carbon parts. The spars are really thick comparing to the plane itself. It looks like it could take a beating. Two main spars, each elevon has a spar and two more spars (L+R) along the leading edge of the plane. This plane constructionwise, is not for beginners. You'll need to cut away some molding residue and the supplied PCB needs a good soldering hand (It's a BEC to power the servo's) Although i'm raving about the good quality, it might look like one wing half is slightly warped. I'll have to look into that. Can't wait to try this one out :D

Качество хорошее, материал плотный! Есть не большие недочеты на всех швах от пресс формы, но аккуратно ножом можно подрезать. модель не супер отлита. Пена вроде спечена плотно. На элевонах нужно ставить петли, но это моё мнение. Комплект весь, но не нет проставки для мотора, Spare Part Motor Mount Product ID: 1150379 - в комплекте её нет! Придется заказывать отдельно. На фотографиях на сайте она присутствует! Цена супер. Покупал во время годовщины интернет магазина. Quality is good, the stuff is tight! There are no big flaws in all seams from the mold, but you can trim it with a knife. the model is not super cast. The foam seems to be sintered densely. On Elevons you need to put a loop, but this is my opinion. The complete set, but there is no spacer for the motor, Spare Part Motor Mount Product ID: 1150379 - in the complete set it is not present! Have to order separately. She is present on the photos on the site! The price is super. Bought during the anniversary of the online store. RCPOiNT

Качество хорошее, материал плотный! Есть не большие недочеты на всех швах от пресс формы, но аккуратно ножом можно подрезать. модель не супер отлита. Пена вроде спечена плотно. На элевонах нужно ставить петли, но это моё мнение. Комплект весь, но не нет проставки для мотора, Spare Part Motor Mount Product ID: 1150379 - в комплекте её нет! Придется заказывать отдельно. На фотографиях на сайте она присутствует! Цена супер. Покупал во время годовщины интернет магазина. Quality is good, the stuff is tight! There are no big flaws in all seams from the mold, but you can trim it with a knife. the model is not super cast. The foam seems to be sintered densely. On Elevons you need to put a loop, but this is my opinion. The complete set, but there is no spacer for the motor, Spare Part Motor Mount Product ID: 1150379 - in the complete set it is not present! Have to order separately. She is present on the photos on the site! The price is super. Bought during the anniversary of the online store. RCPOiNT

Качество хорошее, материал плотный! Есть не большие недочеты на всех швах от пресс формы, но аккуратно ножом можно подрезать. модель не супер отлита. Пена вроде спечена плотно. На элевонах нужно ставить петли, но это моё мнение. Комплект весь, но не нет проставки для мотора, Spare Part Motor Mount Product ID: 1150379 - в комплекте её нет! Придется заказывать отдельно. На фотографиях на сайте она присутствует! Цена супер. Покупал во время годовщины интернет магазина. Quality is good, the stuff is tight! There are no big flaws in all seams from the mold, but you can trim it with a knife. the model is not super cast. The foam seems to be sintered densely. On Elevons you need to put a loop, but this is my opinion. The complete set, but there is no spacer for the motor, Spare Part Motor Mount Product ID: 1150379 - in the complete set it is not present! Have to order separately. She is present on the photos on the site! The price is super. Bought during the anniversary of the online store. RCPOiNT

small but valuable wing i rigged mine with an emax 2205s 2300kv and 30a esc and this thing loves to fly fast and well. if you put a led board on the back like the one in the picture (not mine) it is a perfect race wing. you can also carry it outside your backpack for a mountain ride, it will fly in every condition.

small but valuable wing i rigged mine with an emax 2205s 2300kv and 30a esc and this thing loves to fly fast and well. if you put a led board on the back like the one in the picture (not mine) it is a perfect race wing. you can also carry it outside your backpack for a mountain ride, it will fly in every condition.

small but valuable wing i rigged mine with an emax 2205s 2300kv and 30a esc and this thing loves to fly fast and well. if you put a led board on the back like the one in the picture (not mine) it is a perfect race wing. you can also carry it outside your backpack for a mountain ride, it will fly in every condition.

This little wing is very tough, has a nice finish and is beautiful. The precut holes for the servos, ESC, RX and TX made it very easy to build and give it a very nice finish look. Surprisingly the manual both for the flying wing and the on board PCB is perfect. Speaking of PCB, it is a very nice touch. The center part hole is large for a flying wing of this category, you can easily fit a 3S 2200mhA batterie. Further more the package is well done, no damage and quick delivery (I order two separately) Overall a very good flying wing, thanks!

This little wing is very tough, has a nice finish and is beautiful. The precut holes for the servos, ESC, RX and TX made it very easy to build and give it a very nice finish look. Surprisingly the manual both for the flying wing and the on board PCB is perfect. Speaking of PCB, it is a very nice touch. The center part hole is large for a flying wing of this category, you can easily fit a 3S 2200mhA batterie. Further more the package is well done, no damage and quick delivery (I order two separately) Overall a very good flying wing, thanks!

This little wing is very tough, has a nice finish and is beautiful. The precut holes for the servos, ESC, RX and TX made it very easy to build and give it a very nice finish look. Surprisingly the manual both for the flying wing and the on board PCB is perfect. Speaking of PCB, it is a very nice touch. The center part hole is large for a flying wing of this category, you can easily fit a 3S 2200mhA batterie. Further more the package is well done, no damage and quick delivery (I order two separately) Overall a very good flying wing, thanks!

Pacco arrivato in buone condizioni nella confezione è presente anche un power distribution board con modulo BEC che credevo fosse incluso . Inserito un Flight controller CC3D motore sunnysky X2204 2300 Kv ricevitore frsky V8R7 II ESC EMAX 20A un po grosso bisogna ricavare spazio . Attenzione nel scegliere la posizione per il perno di plastica da forare nell'ala. Tenersi piu distante vedi foto ala sinistra dall'alto.

Pacco arrivato in buone condizioni nella confezione è presente anche un power distribution board con modulo BEC che credevo fosse incluso . Inserito un Flight controller CC3D motore sunnysky X2204 2300 Kv ricevitore frsky V8R7 II ESC EMAX 20A un po grosso bisogna ricavare spazio . Attenzione nel scegliere la posizione per il perno di plastica da forare nell'ala. Tenersi piu distante vedi foto ala sinistra dall'alto.

Pacco arrivato in buone condizioni nella confezione è presente anche un power distribution board con modulo BEC che credevo fosse incluso . Inserito un Flight controller CC3D motore sunnysky X2204 2300 Kv ricevitore frsky V8R7 II ESC EMAX 20A un po grosso bisogna ricavare spazio . Attenzione nel scegliere la posizione per il perno di plastica da forare nell'ala. Tenersi piu distante vedi foto ala sinistra dall'alto.

Cette aile est un tank. si difficile et très bon voleur pour les pilotes débutants et avancés. si vous êtes un débutant, il suffit de commencer avec 3s 1800mah ou 4s 1300mah juste pour garder le plus de poids vers le bas et vous n'avez aucun problème au lancement. Pour les pilotes plus avancés, vous pouvez aller 6s 3000mah pour super long rang et vous devrez accorder les pids pour le rendre facile de lancement. pour les bigginers son parfait parce que n'a pas d'importance combien de fois pour l'encaisser dur, il prendra comme l'homme réel. Super aile. C'est ma 3ème aile S800. un pour moi un pour mon ami comme cadeau et 3ème j'ai commandé coz j'ai juste adoré et j'ai toujours mon vieux s800 avec moi.

This wing is a tank. so tough and very good flier for beginner and advance pilots. if you are a beginner just start with 3s 1800mah or 4s 1300mah just to keep the over all weight down and you have no problem at the launch. for more advanced pilots you can go 6s 3000mah for super long rang and you will have to tune the pids to make it easy launch. For bigginers its perfect because doesn't matter how many times to cash it hard it will take it like real man. Great wing. this is my 3rd S800 wing. one for me one for my friend as gift and 3rd i ordered coz i just loved it and i still have my old s800 with me.

Cette aile est un tank. si difficile et très bon voleur pour les pilotes débutants et avancés. si vous êtes un débutant, il suffit de commencer avec 3s 1800mah ou 4s 1300mah juste pour garder le plus de poids vers le bas et vous n'avez aucun problème au lancement. Pour les pilotes plus avancés, vous pouvez aller 6s 3000mah pour super long rang et vous devrez accorder les pids pour le rendre facile de lancement. pour les bigginers son parfait parce que n'a pas d'importance combien de fois pour l'encaisser dur, il prendra comme l'homme réel. Super aile. C'est ma 3ème aile S800. un pour moi un pour mon ami comme cadeau et 3ème j'ai commandé coz j'ai juste adoré et j'ai toujours mon vieux s800 avec moi.

The concept of the wing is sooooo gooood, I hope it fly how it looks like :)

The concept of the wing is sooooo gooood, I hope it fly how it looks like :)

The concept of the wing is sooooo gooood, I hope it fly how it looks like :)

Easy to build and looks awesome. Perfect product and great finish. Not to mention that it is very resistant . My favorite build so far is with a BR2212 motor and 80 amp esc . I use 2200mah 3s and get 10 to 20 minutes flight time depending on how hard I drive it.

Easy to build and looks awesome. Perfect product and great finish. Not to mention that it is very resistant . My favorite build so far is with a BR2212 motor and 80 amp esc . I use 2200mah 3s and get 10 to 20 minutes flight time depending on how hard I drive it.

Easy to build and looks awesome. Perfect product and great finish. Not to mention that it is very resistant . My favorite build so far is with a BR2212 motor and 80 amp esc . I use 2200mah 3s and get 10 to 20 minutes flight time depending on how hard I drive it.

EPP material with no adjustments, exactly as removed from the mold. Parts fit together pretty well. See attached image for my way of mounting the motor. On the right wing, the foam beads seems to have weaker bonds. Will see after a crash or two :) Easy to glue using "prenandez/Aderpren" (in Romania/Moldova) - the usual shoes glue. Nice non-magnetic screws, but 8 (4+4) strong magnets on the lid. In order to use a magnetic compass close to the center of the wing it will be necessary to remove the magnets and invent an other fixing mechanism for the lid. It fits a APC7x5 propeller if the motor is not too short. I used double adhesive to keep the wings on the main part.

EPP material with no adjustments, exactly as removed from the mold. Parts fit together pretty well. See attached image for my way of mounting the motor. On the right wing, the foam beads seems to have weaker bonds. Will see after a crash or two :) Easy to glue using "prenandez/Aderpren" (in Romania/Moldova) - the usual shoes glue. Nice non-magnetic screws, but 8 (4+4) strong magnets on the lid. In order to use a magnetic compass close to the center of the wing it will be necessary to remove the magnets and invent an other fixing mechanism for the lid. It fits a APC7x5 propeller if the motor is not too short. I used double adhesive to keep the wings on the main part.

EPP material with no adjustments, exactly as removed from the mold. Parts fit together pretty well. See attached image for my way of mounting the motor. On the right wing, the foam beads seems to have weaker bonds. Will see after a crash or two :) Easy to glue using "prenandez/Aderpren" (in Romania/Moldova) - the usual shoes glue. Nice non-magnetic screws, but 8 (4+4) strong magnets on the lid. In order to use a magnetic compass close to the center of the wing it will be necessary to remove the magnets and invent an other fixing mechanism for the lid. It fits a APC7x5 propeller if the motor is not too short. I used double adhesive to keep the wings on the main part.

Love this model. Here is a video of my 4th S800 build: https://youtu.be/FD4a30jmtz0 I recommend this model to beginners and skilled fpv operators. I modded mine a lot but the mods made it fly very good. Buy yours now!

Love this model. Here is a video of my 4th S800 build: https://youtu.be/FD4a30jmtz0 I recommend this model to beginners and skilled fpv operators. I modded mine a lot but the mods made it fly very good. Buy yours now!

Love this model. Here is a video of my 4th S800 build: https://youtu.be/FD4a30jmtz0 I recommend this model to beginners and skilled fpv operators. I modded mine a lot but the mods made it fly very good. Buy yours now!