Avis des clients

Ecrire un commentaire
  • Tous les Commentaires (1438)
  • Image (201)
  • Vidéo (3)
  • Toutes les Étoiles
    • Toutes les Étoiles(1438)
    • 5 Étoile(1381)
    • 4 Étoile(42)
    • 3 Étoile(12)
    • 2 Étoile(1)
    • 1 Étoile(2)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 12/08/2015

    I bought 5 of these units, a small sample to try to replace other units I bought with Banggood that insisted in burning down, one after other and they didn't assume any responsibility to replace them or to solve the problem so I kept purchasing more but then came to a point where it is too much. Actually the reviews on those are mostly repeating what I felt and reported here. Banggood just doesn't allow to write a review after 6 months. Do we have to purchase every six months the same? The current units are installed for two weeks now and seem to perform well. Time will tell if they will endure past the six months...

    Commentaires
    Afficher l'original
  • 27/07/2016

    Очень удобно. Всегда вижу потребление электричества.

    Commentaires
    Afficher l'original
  • 12/12/2016

    I ordered 2 of these items and installed them in my electrical cabinet. See picture. The one on the left indicates the house power usage. The one on the right shows the solar power generation. The units are accurate and well build. The display indicates voltage, current, power and energy with autoscaling. Attention : the current direction is not taken into account, so consumed and produced electricity are all add up in the energy meter.

    Commentaires (1)
    Afficher l'original
  • 02/02/2017

    The input is protected by a 1W 51 ohm resistor and a 0.1uF X2 cap. Inside is the following chipsets: HOLTEK HT1621B 32x4 LCD controller http://www.seeedstudio.com/document/HT1621.pdf Renergy 8208g Single phase metering IC running at 3.579545 MHz http://en.sfkj-tech.com/cp3_1/&productId=83.html ST Micro 32F030F4P6 STM32F0x0 Mainstream ARM Cortex-M0 Value line MCU with 16 Kbytes Flash, 48 MHz CPU running at 8 MHz http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f0-series/stm32f0x0-value-line/stm32f030f4.html

    Commentaires
    Afficher l'original
  • 01/12/2017

    good quality power monitor, it is very easy to connect and use it. the solderings quality is ok and the screen is brilliant and easy to read. I have not checked its precision, but if you need a panel meter for monitoring your power it is a right choice. good value for money Power Monitor di buona qualità, molto facile da collegare e da usare. la qualità delle saldature è ok e lo schermo è brillante e facile da leggere. Non ho controllato la sua precisione, ma se hai bisogno di uno strumento da pannello per monitorare i tuoi consumi è una scelta giusta. buon rapporto qualità prezzo

    Commentaires
    Afficher l'original
  • 15/08/2015

    Tested and it works , after installation just worked 5 minuted before burned out , the strange is seams burned the display not the electronic ... Buy a new one today I hope to be more lucky

    Commentaires
    Afficher l'original
  • 18/11/2020

    Livraison très rapide, l'emballage est bon standard pour Byngood. L'odmètre fonctionne, c'est bien, les relevés volmètres sont exacts, les relevés actuels sont corrects avec une précision de 5%, ce qui est tout à fait acceptable. le bouton peut régler les lectures initiales du compteur d'énergie, réinitialiser tous les compteurs, une petite pression active/désactive l'éclairage. Super appareil ! Je l'ai mis dans le garage. Je recommande!

    Commentaires
    Afficher l'original
  • 23/11/2019

    Very good display monitor. Tested and working fine. Recommended.

    Commentaires
    Afficher l'original
  • 11/09/2017

    Meet je verbruik met dit toestel, werkt perfect en aansluiten is geen probleem. Een ware aanrader voor wie zijn verbruik in de gaten wil houden.

    Commentaires
    Afficher l'original
  • 15/01/2016

    The voltmeter is very accurate. For 229.9V on a multimeter, it shows 229V and for 230.1V on the multimeter it shows 230V. So, it is very accurate, but it disregards the digit after the comma - this leads to a maximum error of about 1V. The amperemeter, has an error of -0.3A. This error is constant over a test period of about 30 minutes and at various loads. The multimeter was recently calibrated. The power calculation is affected by the cosφ, so P =/= U * I. Also, there is an overload alarm - the power section starts to blink if the load exceeeds a user-programmable threshold. The used energy needs more time to observe to result a comparison with the energy-company's meter, but I presume that it will be grossly similar. After a power-down, it holds the last values. The backlight can be enabled/disabled. The products build quality is good enough for the value. The exact model, from the label on the back, is: PEACEFAIR PZEM-061.

    Commentaires (1)
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 126,69€
    • 23,86€
    • 11,01€
    • 47,73€
    • 44,06€
    • 50,49€
    • 90,88€
    • 8,25€
    • 29,37€
    • 12,84€
    • 15,60€
    • 11,93€
    • 11,93€
    • 60,58€
    • 100,98€
    • 119,34€
    • 73,44€
    • 9,53€