Avis des clients

Ecrire un commentaire
  • Tous les Commentaires (364)
  • Image (41)
  • Vidéo (1)
  • Toutes les Étoiles
    • Toutes les Étoiles(364)
    • 5 Étoile(354)
    • 4 Étoile(7)
    • 3 Étoile(2)
    • 2 Étoile(0)
    • 1 Étoile(1)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 03/04/2014

    I used this with a Microchip PIC development board to interface to a 20x4 LCD display. With only 4 wires (including 2 for power) it's simple to set up and uses far fewer ports than the standard LCD parallel interface. As delivered the address pads A0 A1 and A2 are open but pulled high - so the I2C address is 0x4E. Ports P7,P6,P5,P4 of the PCF8574 interface to DB7,DB6,DB5,DB4 of the LCD Display. Port P3 is hard-wired to the backlight via a transistor: 1 = on / 0 = off. It's great that the backlight can be switched on and off via software with no additional hardware required. Port P2 is the display bit clock : E = 1 -> E = 0 active. Port P1 is R/W hardware Read/Write bit hardware : Read = 1 / Write = 0, so reading from the LCD display is possible, if required. Port P0 is RS Register Select : CmdReg = 0 / DataReg = 1. Display driver is HD44780 compliant. A great buy! I won't be interfacing to an LCD in future without it.

    Commentaires
    Afficher l'original
  • 16/05/2015

    I bought some of these and found out that there are different models which need different pin configurations. Here is a beginners guide for the ones from Bangood: http://safe-power.appspot.com/i2c-en.html You need to download one library, and you are ready to enjoy LCDs on your arduino with only 2 Arduino pins occupied (plus GND and VCC). This little board saves you time and pins :-)

    Commentaires
    Afficher l'original
  • 18/01/2019

    Good quality.

    Commentaires
    Afficher l'original
  • 14/02/2021

    Atteint avec succès le Maroc et avec une bonne qualité d'emballage

    Commentaires
    Afficher l'original
  • 09/04/2021

    nice product. its really helpful to reduce the pins needed on a lcd. cool to see that there is a jumper include to enable or disable the onboard led. can be helpful in low power situations. the product was not damaged in shipping and the quality looks great!

    Commentaires
    Afficher l'original
  • 11/09/2020

    Bien reçu en bon ordre et bien emballé. Il faut encore les tester.

    Commentaires
    Afficher l'original
  • 27/02/2017

    The I2C interface module works fine on my blue 1602 LCD module. The I2C address is 0x27 out of the box so remember to modify your code accordingly. There is a very clear description that can be found here: http://arduino-info.wikispaces.com/LCD-Blue-I2C. It clearly describes the different available versions of the I2C interface. The one I received was version 3. When I first connected it and run the sample code I adjusted for the 16x2 display it did not seem to show any information on the display. The root cause was the potentiometer on the I2C interface not to be setup correctly out of the box. I needed to adjust it to change the contrast and show the characters on the screen. So I am happy with this interface as it reduces the connection to only 4 wires (2 for the power supply and 2 for the communication).

    Commentaires
    Afficher l'original
  • 20/08/2013

    After receiving item, I test it with good results. Runs fine.

    Commentaires
    Afficher l'original
  • 08/07/2020

    Fin travaillée à la première tentative. Faites attention à régler correctement le contraste sur le trimmer: les écritures à l'écran peuvent apparaître si sombres que vous pensez que cela ne fonctionne pas. J'ai cherché l'adresse avec un scanner I2C (code facile à trouver sur le site Arduino) et j'ai trouvé mon article 0x27. Pour changer d'adresse, vous devez souder des cavaliers sur les points A0-A1-A2 près du trimmer. Ça a marché sur le premier coup. Veillez à ajuster le contraste avec le trimmer, car le lettrage sur l'écran peut être si feuilleté qu'il ne semble pas fonctionner. L'adresse détectée avec un scanner I2C (peut être trouvé facilement sur le site Arduino) dans mon échantillon était 0x27. Pour changer d'adresse, vous devez souder des cavaliers sur les emplacements A0-A1-A2 près du trimmer.

    Commentaires
    Afficher l'original
  • 19/10/2018

    nice package

    Commentaires
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 9,19€
    • 10,57€
    • 7,35€
    • 10,57€
    • 6,43€
    • 6,43€
    • 11,95€
    • 4,59€
    • 2,89€
    • 8,27€
    • 5,51€
    • 5,51€
    • 6,43€
    • 4,22€
    • 8,49€
    • 13,80€
    • 10,57€
    • 9,51€