Reviews des clients

4.97 sur 5
Ecrire un commentaire
  • Tous les Commentaires (71)
  • Image (5)
  • Vidéo (0)
  • Toutes les Étoiles
    • Toutes les Étoiles(71)
    • 5 Étoile(69)
    • 4 Étoile(2)
    • 3 Étoile(0)
    • 2 Étoile(0)
    • 1 Étoile(0)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
  • July-24 2020 06:19:49

    Nice build, seems sturdy when handled. Strong springs. Needs a screwdriver to open the 9V battery compartment, though.

    Commentaires
  • January-29 2020 08:21:09

    Wszystko działa jak należy.

    Commentaires
  • August-18 2020 15:03:17

    Very good! I tested 12v dc and 230v ac. wotking fine.

    Commentaires
  • September-28 2017 02:09:45

    this AC current probe is an entry level model, but it gives you the opportunity to display on the oscilloscope the waveform of the ac current in your load keepeing everything insulated from the power supply. I made a quick check with a resistor load connected to the output of a 50Hz transformer and the result of the measurement is shown in the photo. As soon as I can I will check the precision of the displayed signal and I will try with higher frequencies and different kind of loads, but it looks

    Commentaires
  • August-08 2019 19:40:38

    The unit works to specification. Bandwidth was measured with ~80mApp and is exactly the specified 20KHz. The zero-ing function was surprisingly precise. A great value for measuring power line inrush surges, but has insufficient bandwidth for full detail of SMPS pulses or ESD transients. Types with much higher bandwidth come at much higher cost. Attached shows square wave response and noise bands at 2KHz and 10mA/div.

    Commentaires
  • February-01 2020 06:11:34

    Great product for hobby work and educational purposes. It seems to work properly although seems to show ~5% higher values on both ranges than my other equipment, so could be a bit out of spec in my case. Probably can be calibrated if needed. Signal noise could be lower, but I usually take average measurements anyway, so it doesn't matter that much to me. For one shot applications, I presume it could be a bit problematic if you need to be sure what are you looking at. Haven't yet tested it at higher

    Commentaires (2)
  • October-23 2020 11:08:12

    Good value for the money. Gives comparable results to much more expensive current clamps in its rated range. Have read other reviews on this current clamp that complain about unwanted oscillations but I can't measure any unwanted oscillations on either of my two units

    Commentaires
  • November-18 2020 02:10:24

    All good. Great price, fast shipping from CZ. The only drawback, that it need's 9V battery.

    Commentaires
  • September-07 2020 07:02:21

    thanks for the shipment

    Commentaires
  • July-25 2020 09:01:10

    Tested on comparison with E3N by Chauvin Arnoux on Hantek DSO 5102P - no difference at all. Great performance for reasonable money

    Commentaires
Show:

    Go to page

    Go

    Vous pourriez être intéressé par

    recommendation for you
    • 92,33€
    • 17,75€
    • 18,59€
    • 72,09€
    • 27,89€
    • 25,36€
    • 18,59€
    • 12,67€
    • 21,98€
    • 34,66€
    • 19,44€
    • 11,41€
    • 25,36€
    • 12,67€
    • 13,52€
    • 15,92€
    • 9,29€
    • 27,05€