Reviews des clients

Ecrire un commentaire
  • Tous les Commentaires (37)
  • Image (3)
  • Vidéo (0)
  • Toutes les Étoiles
    • Toutes les Étoiles(37)
    • 5 Étoile(34)
    • 4 Étoile(2)
    • 3 Étoile(1)
    • 2 Étoile(0)
    • 1 Étoile(0)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 05/09/2017

    Мотор пришел в разобранном состоянии - патрон отдельно в промасленном пакете втулка тоже отдельно. Втулку посадил не с первого раза горячим методом: грел на газу и после немного постукивая посадил на вал но не на всю длину втулки а где-то на 5 мм дальше не пошла. Биения нету заказом доволен. У самого мотора спереди подшипник сзади вроде бы втулка но в моем экземпляре вал прокручивается во втулке переднего подшипника на работоспособность это в принципе не влияет.

    Afficher l'original
  • 07/12/2018

    estupendo,me llegó muy rápido.bien todo, era lo que esperaba y es igual que otro que se me estropeó

    Commentaires (1)
    Afficher l'original
  • 26/12/2018

    very good

    Afficher l'original
  • 13/10/2021


    Afficher l'original
  • 26/05/2021

    un excellent service rapide

    Afficher l'original
  • 01/04/2019

    Motor has maybe 0.3mm end-play, and there's no adapter to fit the 3.17mm shaft into the chuck. The chuck seems to require a Morse taper of around 6.2mm diameter. The chuck itself is nicely made and runs smoothly. The motor and chuck are obviously not assembled as in the photo. Though the parts supplied are good quality, unless you can turn up the Morse taper adapter to connect them together, this will not be useful to you. If you can make the adapter, then it's good value.

    Afficher l'original
  • 14/01/2018

    The motor has front ball bearing and sleeve type rear one. The sleeve bearing does not appear to be a self aligning type. When I received the package, I could not turn the shaft by hand - it was too tight in the bearings. After running it for a few minutes at various speeds the shaft became easier to turn. I was able to test it with no load. This is what I've got. 6V-0.34A-1450 RPM 12V-0.35A-3248 RPM 16V-0.32A-4456 RPM 20V-0.30A-5678 RPM 24V-0.31A-6880 RPM Motor speed and current depend on the bearing resistance, so your numbers may be a little different. The motor shaft is loose in the front bearing and all thrust goes to the rear sleeve. Therefore this motor is not suitable for a hand drill application if you want to get any life out of it. The drill chuck looks good, but I could not test it - adapter was not included in the package. I know it is not shown anywhere in the description, but how else are you going to attach the chuck to the motor shaft? The overall impression - Banggood should stop selling this kit. It will not make anybody happy.

    Commentaires (1)
    Afficher l'original
  • 26/02/2018

    I will not be using it as intended. Please see my separate review of the drill chuck. The motor is good, but 775 motor is way better for drilling application. The package came with all parts included and nothing was damaged. The wires with insulated quick-connect terminals is the best part of this purchase.

    Afficher l'original
  • 02/08/2019

    Hello, the goods has come not compete. I have got only the motor,the two cables with sleews and a small brass roller. Nothing elese. Please send me the missing parts. The pocket was not broken. Thank you. Jaroslav Vojtěch Order Nr. 70269770

    Afficher l'original
  • 23/01/2018

    وصلت الشحنة بحالة جيدة وبمدة وجيزة وهو عبارة عن موتور مع رأس دريل للاستخدام اليدوي الخفيف

    Afficher l'original

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 190,38€
    • 651,59€
    • 160,09€
    • 398,08€
    • 28,97€
    • 180,00€
    • 169,61€
    • 42,79€
    • 83,07€
    • 86,53€
    • 335,53€
    • 309,85€
    • 42,79€
    • 190,38€
    • 145,93€
    • 10,98€
    • 250,96€
    • 23,26€