Avis des clients

Ecrire un commentaire
  • Tous les Commentaires (264)
  • Image (25)
  • Vidéo (0)
  • Toutes les Étoiles
    • Toutes les Étoiles(264)
    • 5 Étoile(240)
    • 4 Étoile(21)
    • 3 Étoile(3)
    • 2 Étoile(0)
    • 1 Étoile(0)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 15/08/2019

    Nice and cheep Product. The LDO is a LM6206, so the max input voltage is 6.5V. The board is based on a TLC555 and outputs a voltage from 3.3V to 0V. It consumes around 4mA at 5V or 3.3V. Wet soil gives a lower voltage than dry soil.

    Commentaires (1)
    Afficher l'original
  • 18/07/2018

    The sensor is based on an a-stable multi vibrator circuit using a 555 where the output duty cycle changes with the sensed capacitance. The simply over an RC circuit integrated signal is the board's output. Unfortunately, the discharge time constant on C (1µF) on this model (Ver. 1.2) seems very high (>10 sec) which is caused by too high valued or non existing discharge resistor. So I simply added a 1.2M resistor from the board's output to ground. There is just enough room at the connector side and already existing via's to easily solder a small 1/10W radial resistor on. This may slightly limit the output swing but gives more stable result voltages.

    Commentaires
    Afficher l'original
  • 09/10/2018

    not yet tested, product as per website description. some fluxant residue on the solder joints. it looks Ok, satisfied non ancora testato, prodotto come da descrizione del sito web. alcuni residui flussanti sui giunti di saldatura. sembra Ok, soddisfatto

    Commentaires
    Afficher l'original
  • 02/10/2020

    Excellent produit et très bien fini.

    Commentaires
    Afficher l'original
  • 25/09/2019

    good price, good quality

    Commentaires
    Afficher l'original
  • 02/09/2019

    Seems good.

    Commentaires
    Afficher l'original
  • 03/07/2019

    These are definitely an upgrade to the older fork sensors, and seem to be coated quite well with some sort of epoxy compound to reduce corrosion. The edges of the board, however, are still raw PCB and I would recommend touching them up with some 2 part epoxy before calibration and use, just to extend the life of the part.

    Commentaires
    Afficher l'original
  • 23/11/2018

    tested Vcc = 3,3V Wide Voltage 2.5 V 0,68 V

    Commentaires
    Afficher l'original
  • 25/04/2021

    excellent mais prudent qui fonctionne avec au moins 4.5v et non 3.3v. parce qu'il monte ne555 intégré qui nécessite au moins 4.5v

    Commentaires
    Afficher l'original
  • 16/07/2019

    Works fine. I use it with an ESP8266. Be careful: ESP8266 analog input's max. voltage is 1 V! The sensor's max. output voltage is at about 2.8 V.

    Commentaires
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 5,28€
    • 17,00€
    • 11,62€
    • 10,57€
    • 9,19€
    • 16,99€
    • 9,19€
    • 4,59€
    • 8,27€
    • 4,22€
    • 4,59€
    • 5,51€
    • 4,59€
    • 10,11€
    • 5,21€
    • 5,51€
    • 10,57€
    • 13,80€