Reviews des clients

Ecrire un commentaire
  • Tous les Commentaires (61)
  • Image (4)
  • Vidéo (0)
  • Toutes les Étoiles
    • Toutes les Étoiles(61)
    • 5 Étoile(60)
    • 4 Étoile(1)
    • 3 Étoile(0)
    • 2 Étoile(0)
    • 1 Étoile(0)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 02/12/2016

    I've said in another review of a similar cutter that these tools feel like good quality, I've now been able to test one and I am so impressed it's not funny, I tested a 13mm version of this end mill on a piece of EN3A, known as 070M20 or C22 is commonly referred to as “Mild Steel” in the engineering industry, using a very sturdy Turret Mill much like a Bridgeport but about 1.5 times the size running the cutter at 2400 RPM taking a 3mm depth cut across the material using hand feed I found that there was minimal chatter or vibration and despite a clear visual tool pattern the surface is very smooth almost silky to the touch and the old fingernail test says that the surface roughness was as good as any cutter could be expected to produce, only time will tell now but I am very confident in the abilities of this family of tools.The images attached are of the one test piece they are a touch blurry but that's no fault of the tool.

    Commentaires
    Afficher l'original
  • 11/07/2018

    Трек не отслеживался. Товар дошел за полтора месяца. Качество фрезы удовлетворило.

    Commentaires
    Afficher l'original
  • 20/01/2020

    bien

    Commentaires
    Afficher l'original
  • 25/03/2019

    muy buena calidad, completo se puede utilizar Nada Más que llege.

    Commentaires
    Afficher l'original
  • 15/12/2020

    Ça a l'air bien, mais je n'ai pas encore eu l'occasion de l'essayer.

    Commentaires
    Afficher l'original
  • 15/10/2018

    Доставка Почтой России в течение 25 суток до Москвы без отслеживания. Упакован в пакет и пластиковый разъемный чехол. Очень доволен товаром и пониженной, по сравнению с Али, ценой.

    Commentaires
    Afficher l'original
  • 19/02/2017

    Bought this thinking it was a boring bar. I got it to work but the inserts don't sit quite right. As a single flute endmill it worked great. Not better than a regular Millburn at 10mm cut it may be cheaper to run. Will angel to experiment. Note the cutter has a very long shank for an endmill. It may even work well as a left hand lathe tool. Will angel to experiment.......

    Commentaires
    Afficher l'original
  • 24/11/2017

    Overall appearance is very good. The surface finish is good and the tool is hardened. However, the insert leaves a bad finish compare to other inserted tooling.

    Commentaires (1)
    Afficher l'original
  • 15/04/2017

    This 10mm boring bar was priced very nicely and worked better than I expected. My initial test was on some stainless steel which is tricky to machine but the result was impressive. Looking forward to using it on something more forgiving. Excellent value and performance!

    Commentaires
    Afficher l'original
  • 02/10/2017

    Товар получил, все как в описание, все высший класс, все ок

    Commentaires
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 25,95€
    • 69,96€
    • 39,80€
    • 21,63€
    • 29,98€
    • 17,30€
    • 27,68€
    • 41,97€
    • 62,96€
    • 19,98€
    • 29,98€
    • 43,97€
    • 39,97€
    • 38,97€
    • 27,98€
    • 15,98€
    • 82,95€
    • 20,98€