Reviews des clients

Ecrire un commentaire
  • Tous les Commentaires (232)
  • Image (29)
  • Vidéo (0)
  • Toutes les Étoiles
    • Toutes les Étoiles(232)
    • 5 Étoile(223)
    • 4 Étoile(6)
    • 3 Étoile(2)
    • 2 Étoile(0)
    • 1 Étoile(1)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 10/11/2016

    Works as specified if you stay in the limits. Just a little warning: during my tests, I lowered the input voltage and under 3.5V, the circuit doesn't cut but becomes crazy and the output (that was set to 15V with the pot.) jumps to 40V with no load. With a 2k resistor at the output, it only goes to 30V. Of course, this is under the specified minimum voltage, but for solar applications, how can you guarantee that the input voltage will not be there? So when it says "Module Suitable For Solar Panel" I'm suspicious. If you really want to use it like that, you could add a small circuit between the solar panels and the converter to cut it if the voltage drops under the minimum 3.8V or clamp the output with a zener (there's no voltage rating on the output capacitor so that kind of overvoltage could damage it if it is not designed to handle 40V) Also the problem with that kind of circuit is that if you try to extract too much current from a solar cell, its voltage drops, but then the converter will try to get even more current to keep it's output and the input voltage drops even more... So you also have to add a circuit that limits the output current when the input voltage drops. Conclusion: good circuit if you use it properly but not really appropriate for solar panels despite what it says in the title.

    Commentaires
    Afficher l'original
  • 27/01/2021

    Sera utilisé à l'avenir avec de vieux PC-alimentation-alimentations pour les tensions variables. Je l'ai testé avec une alimentation électrique et j'ai mesuré la tension de sortie. L'entrée était de 7,2 volts. J'ai utilisé la sortie à des tensions de plus de 25 V jusqu'à 1,5 volts. Le trimmer pour la tension de sortie est extrêmement sensible (potentiomètre à 10 tours) de sorte que la tension exacte peut être réglée facilement. La tension d'entrée doit être de 5 volts ou plus pour une sortie stable.

    Commentaires
    Afficher l'original
  • 27/09/2020

    c'est si beau

    Commentaires
    Afficher l'original
  • 19/02/2017

    I ordered three of these modules. I had never used them before, so I hooked them up to a basic adjustable power supply and measured the output while I made adjustments to the trimpot. I was having problems with the output voltage on the first one I tested, where it wouldn't go below 9.5V, even with a 5V input (I needed 3.3V). The step-up still seemed to work fine. I tried to figure out which component failed, but I never did. I even removed the trimpot for testing and resoldered a couple of surface mount resistors. I tested the second one, and it worked fine. I tested the third one, and it worked fine, but while I was adjusting the trimpot, I encountered the same problem and it jumped up to 9.5 V. I think this was probably due to an error on my part. I think that my alligator clip probably slipped and shorted something out. This also led me to believe that I probably killed the first one in the same manner. My advice is to be very careful when using this module, and to solder wires in place before testing. In my case, I feel that the error was on my part, and I will be ordering some more in the future, since they are inexpensive. Also, the circuit boards on all of mine were misprinted as part DSN600AUD instead of DSN6000AUD. Other than that, they are identical to the one in the picture.

    Commentaires
    Afficher l'original
  • 02/12/2020

    Descendez de DC à DC changeur de DC. Il fonctionne très bien pour de petites charges telles que des ventilateurs ou de petits moteurs à courant continu ou d'autres appareils électroniques. J'aime ça pour mes projets de bricolage.

    Commentaires
    Afficher l'original
  • 25/08/2018

    With a 12V power supply I achieve 1.75V to 47.5V output range, pretty good for the size and can easily be incorporeted inside any electronic project

    Commentaires
    Afficher l'original
  • 21/06/2017

    Device arrived set to 20V output. Left turn Driving a small 19V load from a USB power bank is no problem. If a more powerful source is used and the load uses more power, the temperature can rise quickly. Keep an eye on the power throughput.

    Commentaires
    Afficher l'original
  • 18/04/2017

    Converters work as described. Good price.

    Commentaires
    Afficher l'original
  • 27/12/2016

    All worked normally.

    Commentaires
    Afficher l'original
  • 19/06/2019

    They work great, I was impressed by the resolution of the trimpot and consistency of the voltage output. They have a wide range of input and output voltages and the current is enough for many applications.

    Commentaires (1)
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 7,75€
    • 3,85€
    • 2,88€
    • 6,65€
    • 16,63€
    • 4,81€
    • 7,71€
    • 11,56€
    • 3,03€
    • 15,52€
    • 7,71€
    • 4,81€
    • 4,54€
    • 9,97€
    • 4,43€
    • 11,08€
    • 8,86€
    • 94,24€