Avis des clients

Ecrire un commentaire
  • Tous les Commentaires (477)
  • Image (42)
  • Vidéo (4)
  • Toutes les Étoiles
    • Toutes les Étoiles(477)
    • 5 Étoile(444)
    • 4 Étoile(17)
    • 3 Étoile(7)
    • 2 Étoile(4)
    • 1 Étoile(5)
Trier par:
Commentaire Top
  • Commentaire Top
  • Le plus utile
  • Le plus récent
Avis uniquement de votre pays (France)
|
Afficher l'original

Une partie de la critique a été traduite automatiquement.

  • 24/06/2017

    easy to use - comes with extra motor connection cable - only you must carefully solder this - 2A brushed built in esc works very smooth and good. It is my second low voltage DSM receiver from BG - Now flies in a 600mm wingspan OPEL RAK 1 two 1,7 gr. servos elev. / rudder and 8mm pusher brushed.

    Commentaires (5)
    Afficher l'original
  • 24/05/2020

    Merci aux commentaires que j'ai compris comment se lier à un Spektrum DSM2 DX8 Tx-ignorer ces instructions pour utiliser un connecteur de liaison-il suffit de joindre une batterie 1s et lorsque le rouge Rx lumière de liaison change de rapide à lent-alimenter votre Tx avec bouton de liaison enfoncé sur Tx-une fois lié, vous pouvez allumer le Rx facilement après avoir allumé le Tx Tx. J'ai utilisé un moteur brossé comme fourni dans le kit Black Flyer V2 - vous soudez aux connecteurs de rechange de l'esc intégré. Vous devez régler Tx max basse assiette sur l'accélérateur et la réponse du moteur est bonne avec une plage d'accélérateur satisfaisante et la puissance - J'ai utilisé BG 1g servos qui se branchent facilement. Impressionnant Rx à bon prix - en attente de test de vol bientôt - recommandé! 😊

    Commentaires (1)
    Afficher l'original
  • 09/04/2018

    I use it with my DIY Whitehead. Integrated 2AESC works good with full Lipo on two paralell 720 brushed motors. But low voltage do not work in the way I hoped. At low voltage motors do not stop and the aileron servo begin to spin in various directions. So short flights 3- 4 minutes with a HV 3,V 230mah Lipo are fun enough.

    Commentaires (3)
    Afficher l'original
  • 05/08/2017

    Bought this receiver together with 1.7g servos as recommended by BG for their Minimum Fokker E3. The servo and receiver have incompatible connectors and BG are unable to furnish information on the plug/socket types to enable fabrication of matched leads. None of the 3x items came with instructions or information although a Fokker build thread is on file. Found out that connectors are JST SH 1.0, not available at BG!!!!!!

    Commentaires (1)
    Afficher l'original
  • 02/10/2016

    receiver binds to my dx8, all channels ok. I soldered a 7mm micro brushed motor to the motor output of the receiver but it doesnt work. Motor is OK. Without ESC its worthless for me..

    Commentaires (5)
    Afficher l'original
  • 03/09/2020

    Fonctionne très bien, j'ai cassé le fil de beceause il n'a pas été sécurisé première installation, je l'ai fixé et suis heureux avec elle se lie avec le radiomaster TX16S et a récupéré une petite fée de pente amusante... Whippet vieux reciver brûlé!

    Commentaires (1)
    Afficher l'original
  • 19/09/2019

    This tinny rc work just dsm2 any tx.I use spektrum but step one plug battery, 2step blink rarely wait few seconds come blinking speed, 3 step open your tx in bind mid after that in 2 sec leds red becomes solid and voile means done can put for any toys plane or heli all connectors is 3pins i wiil lock on rc group forum what is any contact have for aileron ,rudder etc.

    Commentaires
    Afficher l'original
  • 11/07/2017

    Passt genau zum "Robur" von Busch in 1:87. Armin

    Commentaires (3)
    Afficher l'original
  • 10/06/2019

    I'm flying this micro receiver in a little plane made from 3mm sheet foam from discarded supermarket meat trays (styrofoam). The receiver binds easily with my Spektrum module/ Futaba radio. Motive power is a 8.5mm x 20mm coreless motor (Chaoli from BG) turning a 45mm propeller. 180ma LiPo provides several minutes of high speed fun outdoors in moderate conditions. The built-in 2A speed controller seems to have no problem with this combination even when running full throttle for almost the entire flight. The servo plugs on this receiver are the same as the E-Flite micro brick. I bought some of these connectors and spliced them on a couple of 1.7g micro servos to complete the system. The little plane is very lively in the air and really keeps you busy on the transmitter sticks! This is second time I have purchased one of these units and I'm happy with both of them.

    Commentaires
    Afficher l'original
  • 17/07/2017

    This Rx for 3.7v low voltage is just great. you solder a 2-wire Coreless motor to it or plug in a 3-wire brushless motor. The connections are MINI MICRO 1.0 PH 3-PIN, so be sure your servos have these connectors (Orlandoo 1.7 come with the wrong connector and you have to adapt). The white ones from HEXTRONIK come with the right connector.. I've had to resolder the wires back on, they use a tiny gauge wire. I soldered on a 22 ga. wire nipple that doesn't bend with every movement or adjustment you make when stuffing the electrical parts in side an aircraft. For the price it's fair enough I bought a 2nd one to avoid changing all the time...

    Commentaires
    Afficher l'original
Show:

    Total 0 pages

    Aller à la page

    Vous pourriez être intéressé par

    recommendation for you
    • 17,43€
    • 6,24€
    • 15,89€
    • 23,22€
    • 9,69€
    • 47,80€
    • 19,27€
    • 5,50€
    • 16,52€
    • 76,19€
    • 10,10€
    • 9,49€
    • 62,65€
    • 8,71€
    • 9,49€
    • 28,45€
    • 10,55€
    • 14,68€