2.2KW 220 V AC 12A Monophasé Fréquence Variable Onduleur à Usage Général Gris
Une partie de la critique a été traduite automatiquement.
reçu après seulement une semaine !!!!! carton très robuste,produit conforme à la description,je le voyait un peu plus gros que sur les photos. sera monté sur une fraiseuse.
Les chars banggood
Bien
Cet appareil est conçu pour contrôler votre broche. Je l'ai acheté pour ma broche - 1.5KW, 8.0A, 230V, 3 phases. Je l'ai fait livrer en Pologne en deux semaines. L'onduleur ressemble exactement aux images. Le panneau de commande peut être détaché du boîtier. Vous pouvez même vous débarrasser de l'ensemble du boîtier gris et peut - être monter l'électronique et le panneau de commande séparément. Afin d'utiliser cet onduleur avec votre broche, VOUS DEVEZ régler tous les réglages correctement, selon les spécifications de votre broche. N'essayez PAS de démarrer votre broche sans configurer TOUS les paramètres ! Cela va très probablement brûler la broche et l'appareil! Cet onduleur est configuré pour utiliser 12A par défaut, même si le manuel indique qu'il devrait être 3A. Vous DEVEZ changer les paramètres, rappelez-vous! Vous obtiendrez manuel (en anglais) avec tous les réglages expliqués dans la boîte avec cet onduleur. Ensuite, vous devez passer un certain temps à apprendre ou à rechercher dans l'Internet comment configurer tout en fonction de vos spécifications de broche. Rappelez-vous que cet appareil (ainsi que votre broche) doit être mis à la terre!
Ce sont de super petits VFD. Les instructions manquent sérieusement de détails, mais c'est comme tous les autres là - bas de sorte que vous pouvez obtenir l'information dont vous avez besoin hors du net avec une simple recherche. Youtube a beaucoup de vidéos sur cette vidéo. J'ai encore besoin d'un deuxième, mais le prix sur cette unité semble fluctuer 20bucks pour une raison quelconque. Dites - moi quand vous le prix à nouveau à 69bucks et je vais prendre un autre!
... for single phase supply and three phase output. Haven't yet made the final mechanical installation of the three phase 1.5 kW motor on my lathe. Still need some pulleys a belt tension adjuster and a permanent mount(/belt tension adjuster) for the motor. The electrical installation and inverter setup is ok and motor runs nicely. I hope that the torque is sufficient at low rpms for whatever I might turn in my lathe.
Received the VFD UNITS today, and i haven't had time to look at them........ Did I mention I ordered two of these units?? One is going to be for my 13 x 40 GAP BED LATHE UPGRADE and the other VFD will be for my 20 inch MILL CONVERSION....... But first I have to purchase the 3 PHASE MOTORS and ELECTRICAL PARTS.............. It will be awhile for this project to finish.........
Inverter arrived intact with no dings or loose bits. The 'manual' is good english but has all 3 models in it, the AT1, which is mine, does not show an earthing point so i'll need to work that one out. Looking forward to getting it uyp and runnung
This is a great VFD. I looks great quality. The instructions are very well written and the unit is very straight forward to connect with clearly marked terminals. Also it is easy to program if you follow the instructions. Recommended in every way.
It looks like a very good product. Good documentation, good look, package satisfactory, but coul be improved. The first tests are OK. I didn't test it at maximum power, but i'll do it soon. Parameter programming is easy, following the included instruction sheet.